Sản phẩm > Máy và thiết bị sau in > Máy bế & ép nhũ tự động BRAUSSE



Automatic Foil Stamping Machine with Diecutting & Stripping Capabilities



  • Patent turbo spiral air blower pressing foot at feeder head
  • Four pick up and four forward suck heads with angle adjustment
  • Preloading device with rail cart and scaled gate
  • Non – stop feeder with automatic pile lift
  • Left and right side turbo air blower
  • Motorized side adjustment of pallet table
  • Electrical double sheet control
  • Fine air blast at lead edge for smooth thin paper transport
  • Sheet slow down device of feeder belts to assure accurate position of the sheet to the front lays with selective on/off switch
  • Synchronizing device to adjust the sheet positioning to the front lay by hand during production
  • Bullet catcher on the feeder entrance
  • Side lays on both sides push and pull convertible
  • Electronic side lay control to check the sheet position
  • Four individually adjustable front lays with dial read out at the operation side of the machine
  • Two electronic front lay controls by means of Omron Glasfiber optik to control the sheet arrival
  • Photo sensor safety barrier at pallet table floor lever touching point

Die cutting Section

  • Precision worm gear crank toggle driving system to ensure smooth and dynamic lower platen movement
  • Precision stationery upper platen
  • Sandwich hardened cutting plate
  • Pneumatic push button diechase locking mechanism to ensure safe and operator friendly changing of the die
  • Pneumatic clutch/brake for main drive system
  • Servo motor drive automatic impression on/off
  • Digital diecutting pressure tonnage display with maximum pressure limit protection
  • Seven high precision alloy gripper bar
  • High quality pre – stretched gripper bar driving chain
  • State – of – art 3 cam index gripper bar driving system to ensure smooth and precise gripper bar intermittent movement
  • Torque limit safety clutch to protect the index driving system in case of gripper bar crash
  • Double cam driven gripper opener and front lay swing frame without position restore spring for smooth and accurate sheet register and take off
  • Air blasting nozzle bar for stretching the thin paper before die cutting

Stripping Section

  • Triple action movement of the upper and lower stripping frames with lower spring loaded stripping pins
  • Motorized upper frame suspending hoister
  • Upper and lower stripping tool mounting frame can be pulled out for job set up and make ready
  • Remote control operation panel for jogging the upper frame up and down, easy and safe stripping tool set up and alignment
  • Quick stripping tool exchange device (optional)
  • Mechanical disconnecting of lower stripping frame when it is not in use

Delivery Section

  • Automatic delivery with non – stop curtain. This curtain moves into the delivery to catch the arriving sheets during the pile exchange
  • Five section brush brake each section angle adjustable individually
  • Air blower to press down the sheets
  • Rare and side joggers with easy position adjustment
  • Gripper edge stripping and removing system with conveyor belt to remove the gripper edge waste sideways to the drive side
  • Tape inserter with counter
  • Safety device to prevent the steel pile plate from clamping on the foot when it reaches at ground level


Specifications hot foil stamping unit:

Foil advancing shaft: 2 (3rd as optional)  
Maximum capacity foil diameter: Ø 200 mm
Foil core diameter: 1² or 3²
Number of rewind shafts: 6
Number of dancing rollers: 6
Maximum rewinding diameter: Ø 400 mm
Maximum foil and stamping size: 730 x 1020 mm
Maximum foil stamping speed (subject to paper, foil and stamping die quality as well as operator skill)
Foil pull length < 200 mm Foil width ≥ 100 mm
Foil pull length < 300 mm Foil width ≥ 100 mm
Foil pull length < 600 mm Foil width = 150 mm
Foil pull length 600 - 700 mm Foil width ≥ 100 mm
6000 sheets/h
5000 sheets/h
4000 sheets/h
3500 sheets/h
The max. mechanical speed is also 7500 Cycles/H  
Minimum foil width: 45mm
Number of heated zones: 12
Temperature range: 0-200°C
Power for heating: 24 KW

Specifications of paper stock range:

Maximum sheet size: 1050 x 750 mm
Minimum sheet size: 400 x 370 mm
Process able materials:  
1. Paper (depending on quality), min.: 80 – 90 g/m2
2. Carton (depending on quality), up to: 600 g/m2
3. Corrugated board (Fine), up to: 4 mm
(*) Admissible undulation: 4% of the sheet width  
Minimal gripper edge: 9.5 mm

Specifications for die-cutting:

Maximum die cutting size: 1040 x 720 mm
(Maximum cutting size can be reached at 1040 x 730 mm when the quick locking system is dismantled from the die chase)
Inner size of chase: 1145 x 755 mm
Dimensions die-cutting plate: 1080 x 736 mm
Maximum die-cutting pressure: 300 T
Maximum mechanical speed: 7500 cycles/hour

General specifications:

Power supply for main motor: 10 KW.
Power supply for other motors: 9 KW.
Total power supply including heating: 60 KW.
Power voltage: 220V 50/60Hz
Pile height feeder, maximum: 1530 mm (incl. pallet)
Pile height feeder with Non-Stop operation, maximum: 1130 mm (incl. pallet)
Pile height delivery, maximum: 1300 mm (incl. pallet)
Pile height over Non-Stop curtain maximum: 80 mm
Total length (incl. preloading rails): 7016 mm
Total width (incl. catwalk): 4049 mm
Total height (incl. raise 200 mm): 2167 mm
Total net weight: Approx. 17.5 ton

Sản phẩm liên quan